CASPIAN OILFIELD SERVICES İNC. IN 2016 BECAME THE REPRESENTATIVE FOR THE TERRITORY OF AZERBAIJAN.
Pharos Marine Automatic Power, Inc. has provided products for some of the most famous navigation projects around the world, including the first oil rigs off the coast of Texas and the first buoys for the Panama Canal. Today PMAPI operates worldwide from offices in the United States, United Kingdom, and Singapore.
Drill Collar
DP-Master drill collar bars are heat-treated in our modern quench and temper plant and only the highest quality raw material from world-class mills is used . DP-Master utilizes AISI 4137H and 4145H modified steel. Drill collars are manufactured in sizes from 3 1/8” OD to 11” OD in accordance with API Spec 7-1 and NS-1 specifications. Drill Collars can also be supplied in our proprietary sour service material.
Duplex FA-250EX962 |
|
FEATURES
• All serviceable components on tower
• Up to 1640 ft. separation between LED engine and power supply
• Patented optics eliminate ground scatter
• Patented heat pipe thermal management system eliminates need for moving parts; this highly efficient, passive cooling system gives the LED array the highest design life in the marketplace (greater than 60,000 hours)
|
|
| |
|
FA-143-LED Bridge Light |
FEATURES
• High output, low power LEDs arranged in a redundant, symmetric array around the lens focal point
• No routine maintenance is required and power consumption is less than 7 watts
• Stainless steel hardware and lens‐protection rods (angled to minimize shadows in the optical plane)
• A stud base which matches a 2” pipe coupling flange (Usually these are mounted on galvanized steel swivel suspensions (our FA‐230) from the bridge deck or on pedestals on the bridge fenders)
• Control electronics and a 120 VAC power supply located inside the lantern below the array
• Lantern hinge at the middle to facilitate access to the LED array, control electronics and power supply
• Lightning and surge‐suppression circuitry that automatically resets after an inciden
|
|
|
| |
|
FA-165-AIL Area Illumination |
|
FEATURES
• Supplied with four user selectable reflectors to provide a beam dispersion of either 12, 28, 42 or 48°
• AC model 90‐264VAC input, approx. 25W
• DC model 12VDC input, approx. 16W
• All electronics are internal to the lantern in the standard configuration. Mounts base up, down or any angle in between
• Several options for electronic controllers: 90‐264 VAC 50‐60 Hz internal controller, 20‐30 VDC internal controller, External AC or DC controller, which can be remotely located up to 500 meters away
• Integrated heat pipe eliminates need for cooling fan
• No moving parts
|
|
| |
|
FA-165HA Class 1 Helideck |
FEATURES
• Two options for electronic controllers: 90‐264 VAC 50‐60 Hz internal controller, 10‐30 VDC internal controller
• Integrated heat pipe eliminates need for cooling fan
• No moving parts
• Cover is tempered toughed glass, able to withstand high temperature and impact
• Base is impregnated, anodized and painted cast marine grade aluminum
• Stainless steel hardware
• Four 7mm diameter mounting holes. 229 mm (9”) x 191 mm (7 17/32”)
|
|
|
| |
|
FA-165HA Red LED Aviation |
|
FEATURES
• Several options for electronic controllers: 90‐264 VAC 50‐60 Hz internal controller, 10‐30 VDC internal controller, External AC or DC controller, which can be remotely located up to 500 meters away
• Integrated heat pipe eliminate s need for cooling fan
• No moving parts
• Cover is tempered toughed glass, able to withstand high temperature and impact
• Base is impregnated, anodized and painted cast marine grade aluminum
• Stainless steel hardware
• Four 7mm diameter mounting holes. 229 mm (9”) x 191 mm (7 17/32”)
|
|
| |
|
FA-165HA Red LED Subsidiary |
FEATURES
• Two options for electronic controllers: 10‐30 VDC internal controller, External AC or DC controller, which can be remotely located up to 500 meters away
• Integrated heat pipe eliminates need for cooling fan
• No moving parts
• Cover is tempered toughed glass, able to withstand high temperature and impact
• Base is impregnated, anodized and painted cast marine grade aluminum
• Stainless steel hardware
• Four 7mm diameter mounting holes. 229 mm (9”) x 191 mm (7 17/32”)
|
|
|
| |
|
FA-165 Short Range Lantern |
|
FEATURES
• Vertical Divergence from ‐20 to +90 degrees for 360° in the horizontal
• Equivalent Detection Range due to increased vertical divergence: +6 NM
• 256 user selectable flash codes
• Power settings are user selectable
• No moving parts
• Cover is tempered toughed glass, able to withstand high temperature and impact
• Base is impregnated, anodized and painted cast marine grade aluminum
• Stainless steel hardware
• Four 7mm diameter mounting holes. 229 mm (9”) x 191 mm (7 17/32”)
|
|
| |
|
FA-165EX Zone 1 Helideck |
|
FEATURES
• Two options for electronic controllers: 90‐264 VAC 50‐60 Hz internal controller, 10‐30 VDC internal controller
• Integrated heat pipe eliminates need for cooling fan
• No moving parts
• Cover is tempered toughed glass, able to withstand high temperature and impact
• Base is impregnated, anodized and painted cast marine grade aluminum
• Stainless steel hardware
• Four 7mm diameter mounting holes. 229 mm (9”) x 191 mm (7 17/32”)
|
|
|
| |
|
FA-165EX Red LED Aviation |
|
FEATURES
• Several options for electronic controllers: 90‐264 VAC 50‐60 Hz internal controller, 10‐30 VDC internal controller, External AC or DC controller, which can be remotely located up to 500 meters away
• Integrated heat pipe eliminate s need for cooling fan
• No moving parts
• Cover is tempered toughed glass, able to withstand high temperature and impact
• Base is impregnated, anodized and painted cast marine grade aluminum
• Stainless steel hardware
• Four 7mm diameter mounting holes. 229 mm (9”) x 191 mm (7 17/32”)
• Maximum internal power dissipation 40W
|
|
| |
|
FA-165EX Red LED Repeater |
FEATURES
• Two options for electronic controllers: 90‐264 VAC 50‐60 Hz internal controller, 20‐30 VDC Helideck Status Light Controller, which can be remotely located up to 500 meters away
• 40W maximum internal power dissipation
• Integrated heat pipe eliminates need for cooling fan
• No moving parts
• Cover is tempered toughed glass, able to withstand high temperature and impact
• Base is impregnated, anodized and painted cast marine grade aluminum
• Stainless steel hardware
• Four 7mm diameter mounting holes. 229 mm (9”) x 191 mm (7 17/32”)
|
|
|
| |
|
FA-165EX Red LED Aviation |
|
FEATURES
• Several options for electronic controllers: 90‐264 VAC 50‐60 Hz internal controller, 10‐30 VDC internal controller, External AC or DC controller, which can be remotely located up to 500 meters away
• Integrated heat pipe eliminate s need for cooling fan
• No moving parts
• Cover is tempered toughed glass, able to withstand high temperature and impact
• Base is impregnated, anodized and painted cast marine grade aluminum
• Stainless steel hardware
• Four 7mm diameter mounting holes. 229 mm (9”) x 191 mm (7 17/32”)
• Maximum internal power dissipation 40
|
|
| |
|
FA-249 Gimbaled 15 NM |
FEATURES
• 4 linear arrays of very high flux LED's individually mounted in a parabolic reflector and driven by specially designed electronics
• LED's are mounted on specially designed heat sinks to keep the temperature of the LED below 120° C to assure the design life of 60,000 hours
• Gimbal hinges are of a special polypropylene material tested to 69 million flex cycles (no metallic parts)
• The heavy silicone fluid in which the gimbal counterweight is immersed maintains a viscosity of 100,000 SSU at all operating temperatures; this dampens any violent buoy motion and lengthens the natural period of the mechanism to over nine seconds
• External electric control module
• 255 Pre‐programmed flash rhythms
• 360° horizontal beam; uniformity within ±20%
|
|
|
| |
|
FA-249 Gimbaled Incandescent |
|
FEATURES
• Pre‐focused T3.5, S‐8, or S‐11 envelope and C‐8 or CC‐8 filament, incandescent or tungsten halogen lamps to 150 watts
• 4‐ or 6‐place motor driven, APCL‐5/APCL‐10 FLASHCHANGER® with selectable flash rhythms, pulse width modulation regulation, solar charge regulator, monitoring, synchronization, self‐test function, communications port, photocell, and enhanced environmental protection
• Gimbal hinges made of a special polypropylene material tested to 69 million flex cycles (no metallic parts)
• Heavy silicone fluid in which the gimbal counterweight is immersed maintains a viscosity of 100,000 SSU at all operating temperatures, which dampens any violent buoy motion and lengthens the natural period of the mechanism to over 9 seconds
• The FA‐249 Gimbaled Lantern is listed by the U. S. Coast Guard as an acceptable lens/lamp combination in Title 33 Code of Federal Regulations Part 67 for Class "A" structures for use on tension leg platforms to 9° tilt
|
|
| |
|
FA-249 Gimbaled LED |
FEATURES
• 4 linear arrays of very high flux LEDs individually mounted in a parabolic reflector and driven by specially designed electronics
• LEDs are mounted on specially designed heat sinks to keep the temperature of the LED below 50°C to assure the design life of 60,000 hours
• Gimbal hinges are of a special polypropylene material tested to 69 million flex cycles (no metallic parts)
• The heavy silicone fluid in which the gimbal counterweight is immersed maintains a viscosity of 100,000 SSU at all operating temperatures; this dampens any violent buoy motion and lengthens the natural period of the mechanism to over nine seconds
• External electric control module
• 15 pre‐programmed flash rhythms plus 1 for user programming
• 360° horizontal beam; uniformity within ±10%
• Approved by the U. S. Coast Guard for use on Class A structures in the 8th Coast Guard District at 4 watts
|
|
|
| |
|
FA-250EX APCL 5-10 |
|
FEATURES
• Variety of non‐hazardous certified internals can be used due to the nature of the flameproof, IP‐67 enclosure approval
• M20 or M25 quad cable entries remove the need for additional junction boxes
• Lens cover and the cast‐aluminum base are the most durable and longest life system in use
• Smooth acrylic lens cover, the FA‐250EX lantern eliminates the buildup of fillets of moisture, dust, salt spray, raindrops and other contaminants on the internal Fresnel lens prisms
• When fitted with an APCL‐Series FLASHCHANGER®, the FA‐250EX lantern becomes the most versatile product on the market
• Configured as a 10‐mile, Morse U light, the lantern will accept an input voltage of 12, 18, 24 volts and, with an internally mounted DC‐DC converter, 130VDC and operate a 12 volt, 2000 hour 35 watt tungsten halogen lamp
• Low maximum surface temperature of the fixture during operation; the 10‐mile lantern has a maximum of 100°C (T5) at Tamb of 40°C where competing units are 200°C (T3)
• FA‐250EX932: APCL‐10 Six‐place FLASHCHANGER® up to 150 watts
• FA‐250EX952: APCL‐5 Six‐place FLASHCHANGER® up to 60 watts
|
|
| |
|
FA-250EX 322 |
FEATURES
• Available in models approved for ATEX Zone 1 and 2 environments or CSA Field Certified for NEC
Class 1 Division 2 Group C and D, T4, or Ex d IIB T4/5/6 Hazardous Areas
• 320 mm precision molded Fresnel lens
• ATEX certified Zone 1 Ex ‘d' transparent enclosure
• Single xenon flash tube rated for 2 years life
• External controller may be located remotely from the flash head
• External controller provides flash control, photocell input (auto, on, off), synchronization terminal
and monitoring via form C contacts
|
|
|
| |
|
FA-250EX 962 |
|
FEATURES
• Designed to be placed in remote locations, the lantern incorporates very long lived LEDs to minimize schedule maintenance
• Features high flux LED arrays mounted on a stainless steel, parabolic reflector; highly efficient reflector uses a state of the art dichroic hybrid spectral metal coating
• LEDs are mounted on metal core PCBs with patented integrated heat pipes to cool the LED arrays without a cooling fan
• LED array has the highest design life in the marketplace (greater than 60,000 hours)
• Materials of the FA‐250EX962 housing are selected to match the life of the LED contained inside
• No plastic is used in the unit
• Tempered glass cover, able to withstand high impact; base is impregnated, anodized and painted cast aluminum
• AM‐11 electronic controls, which provide current limiting to the LED, flash control, monitoring output, photocell input and a synchronization terminal
• No moving parts
|
VARIATIONS OF LANTERN
• FA‐250EX962‐15 mile: 300 Watt LED Array providing Flashing 15‐mile Morse U White Light. Average power 50W
• FA‐250EX962‐10 mile: 25 Watt LED Array providing Flashing 10‐mile Morse U White Light. Average Power 4.2 watts
• FA‐250EX962‐3 mile: 5 Watt LED Array providing Flashing Morse U 3‐mile Red Light. Average Power 1.0 watts
• FA‐250EX962‐L‐864: 45 Watt LED Array that complies with ICAO Type B or Type C, Flashing or Fixed Medium Intensity Aviation Obstruction Light
|
|
| |
|
FA-250EX 962 Helideck |
FEATURES
• Zone 1 and Safe Area enclosures available
• CAP 437 Compliant
• Transparent enclosure is comprised of a cast base of marine grade aluminum, an upper section with a tempered glass globe cemented into a support ring and a tapered spigot joint (flame path)
• LEDs are mounted on metal core PCBs with integrated heat pipes to cool the LED arrays without a cooling fan
• This highly efficient, passive, cooling system gives the LED array the highest design life in the marketplace (60,000 hours)
• The AM‐11 external electronic controls for the FA‐250EX 962 HSL may be located as much as 800 meters away from the flash head with a 24 VDC input
• AM‐11 provides current limiting, flash control, photocell input (auto, forced on, forced off), and synchronization
|
|
|
| |
|
FA-250HA LR 18NM |
|
FEATURES
• LEDs mounted on specially designed patented heat sinks to keep the temperature of the LED below 50°C to assure the design life of 60,000 hours
• Stacked array of high flux, high efficiency 1x16 Procyon LED Light Engines > 90% efficiency
• 15+1 selectable power level settings (one selectable)
• 256 Selectable flash rhythms
• Terminals for UNIFLASH® III wireless synchronization system or hardwired sync circuit (Optional)
• ATONIS ready for AIS Msg 21 and Msg 6 monitoring
• Utilizes a long range LED optic with a nominal range of up to 28 NM (T=0.85)
• 360° horizontal beam at 3.2° vertical divergence to 50% (8° to 10%)
|
|
| |
|
FA-250HA LED MR 12MN |
FEATURES
• Nominal range of up to 19.5 nautical miles (T=0.85)
• LEDs mounted on specially designed patented heat sinks to keep the temperature of the LED below
50°C to assure the design life of 60,000 hours
• Stacked array of high flux, high efficiency 1x6, or 1x9 Procyon LED Light Engines > 90% efficiency
• 15+1 selectable power level settings (one selectable)
• 256 Selectable flash rhythms
• Terminals for UNIFLASH® III wireless synchronization system or hardwired sync circuit (Optional)
• ATONIS ready for AIS Msg 21 and Msg 6 monitoring
• Utilizes a long range LED optic with a nominal range of up to 28 NM (T=0.85)
• 360° horizontal beam at 3.2° vertical divergence to 50% (8° to 10%)
• 3 tier units and all AC units require external controller
|
|
|
| |
|
LED Litepipe® IV |
|
FEATURES
• Extruded clear acrylic tube, 6” in diameter, which houses the LED light source and patented optical elements
• Sealed tube is lined with opaque diffusing material
• Easy Access: LED rail can be removed and replaced from the top of the LITEPIPE®
• 180° or 360° Emitting Sector
APPLICATIONS
• Bridge Pier Markers and Center Channel Markers
• Range (Leading Light) Light systems
• Locks – side and entry Markers
• Ferry Slip Entry Markers
• Canal Side and Entry Markers
|
|
| |
|
Single Lift Class A Skid |
|
LANTERN FEATURES
• FA‐250LED lantern with 155 mm clear, red, green, yellow, or blue acrylic lens
• Extremely high flux, compact LEDs mounted on a heavy duty heat sink and enclosed inside a sealed housing; the heat sink maximizes the life of the LED array by keeping the maximum temperature of the array to less than 50°C
• Heavy duty STABRITE® system designed to maximize the life of the LED array by providing a secondary environmental enclosure independent of the lantern housing, ensuring moisture does not reduce the life of the LED
• LED array/diffuser system that approximates a marine signal lamp located at the focal point of the lens to maximize the output of the lantern in the horizontal plane with horizontal uniformity of the beam
• Smooth, protective acrylic lens cover eliminates the buildup of fillets of moisture, dust, salt spray, raindrops and other contaminants on the internal Fresnel lens prisms
|
|
SOUND SIGNAL FEATURES
• LIEX 710/023 2 mile sound signal (LIEX 710/022 optional)
• Input voltage: 10.5‐30 VDC
• Input Power to Horn: 100 Watts
• Input Power to Driver: 56 Watts
• Nominal Range: 2 Mile
• Frequency: 670 Hz / 660 Hz
• Morse code: 2‐18 (10%)
• Power Supply: 12 V DC solar generator
|
|
